Blowout (well drilling)

A blowout is the uncontrolled release of crude oil and/or natural gas from an oil well or gas well after pressure control systems have failed.[1]

Prior to the advent of pressure control equipment in the 1920s, the uncontrolled release of oil and gas from a well while drilling was common and was known as an oil gusher, gusher or wild well.

Contents

History

Gushers were an icon of oil exploration during the late 19th and early 20th centuries. During that era, the simple drilling techniques such as cable-tool drilling and the lack of blowout preventers meant that drillers could not control high-pressure reservoirs. When these high pressure zones were breached the hydrocarbon fluids would travel up the well at a high rate, forcing out the drill string and creating a gusher. A well which began as a gusher was said to have "blown in": for instance, the Lakeview Gusher blew in in 1910. These uncapped wells could produce large amounts of oil, often shooting 200 feet (60 m) or higher into the air.[2] A blowout primarily composed of natural gas was known as a gas gusher.

Despite being symbols of new-found wealth, gushers were dangerous and wasteful. They killed workmen involved in drilling, destroyed equipment, and coated the landscape with thousands of barrels of oil; additionally, the explosive concussion released by the well when it pierces an oil/gas reservoir has been responsible for a number of oilmen losing their hearing entirely; standing too near to the drilling rig at the moment it drills into the oil reservoir is extremely hazardous. The impact on wildlife is very hard to quantify, but can only be estimated to be mild in the most optimistic models — realistically, the ecological impact is estimated by scientists across the ideological spectrum to be severe, profound, and lasting.[3]

To complicate matters further, the free flowing oil was — and is — in danger of igniting.[4] One dramatic account of a blowout and fire reads,

"With a roar like a hundred express trains racing across the countryside, the well blew out, spewing oil in all directions. The derrick simply evaporated. Casings wilted like lettuce out of water, as heavy machinery writhed and twisted into grotesque shapes in the blazing inferno."[5]

The development of rotary drilling techniques where the density of the drilling fluid is sufficient to overcome the downhole pressure of a newly penetrated zone meant that gushers became avoidable. If however the fluid density was not adequate or fluids were lost to the formation, then there was still a significant risk of a well blowout.

In 1924 the first successful blowout preventer was brought to market.[6] The BOP valve affixed to the wellhead could be closed in the event of drilling into a high pressure zone, and the well fluids contained. Well control techniques could be used to regain control of the well. As the technology developed, blowout preventers became standard equipment, and gushers became a thing of the past.

In the modern petroleum industry, uncontrollable wells became known as blowouts and are comparatively rare. There has been a significant improvement in technology, well control techniques and personnel training that has helped to prevent them occurring.[1] From 1976 to 1981, 21 blowout reports are available.[1]

Notable gushers

  1. The Shaw Gusher in Oil Springs, Ontario, was North America's (and possibly the world's) first oil gusher. On January 16, 1862, it shot oil from over 60 metres (200 ft) below ground to above the treetops at a rate of 3,000 barrels (480 m3) per day, triggering the oil boom in Lambton County.[7]
  2. Lucas Gusher at Spindletop in Beaumont, Texas in 1901 flowed at 100,000 barrels (16,000 m3) per day at its peak, but soon slowed and was capped within nine days. The well tripled U.S. oil production overnight and marked the start of the Texas oil industry.[8]
  3. Masjed Soleiman, Iran in 1908 marked the first major oil strike recorded in the Middle East.[9]
  4. [[Dos Bocas]] in the State of Veracruz, Mexico, was a famous Mexican blowout that formed a large crate, and leaked oil from the main reservoir for many years, even after Pemex nationalized the Mexican oil industry in March 1938.
  5. Lakeview Gusher on the Midway-Sunset Oil Field in Kern County, California of 1910 is believed to be the largest-ever U.S. gusher. At its peak, more than 100,000 barrels (16,000 m3) of oil per day flowed out, reaching as high as 200 feet (60 m) in the air. It remained uncapped for 18 months, spilling over 9 million barrels (1,400,000 m3) of oil, less than half of which was recovered.[2]
  6. A short-lived gusher at Alamitos #1 in Signal Hill, California in 1921 marked the discovery of the Long Beach Oil Field, one of the most productive oil fields in the world.[10]
  7. The Barroso 2 well in Cabimas, Venezuela in December 1922 flowed at around 100,000 barrels (16,000 m3) per day for nine days, plus a large amount of natural gas.[11]
  8. Baba Gurgur near Kirkuk, Iraq, an oilfield known since antiquity, erupted at a rate of 95,000 barrels (15,100 m3) a day in 1927.[12]
  9. The Wild Mary Sudik gusher in Oklahoma City, Oklahoma in 1930 flowed at a rate of 72,000 barrels (11,400 m3) per day.[13]
  10. The Daisy Bradford gusher in 1930 marked the discovery of the East Texas Oil Field, the largest oilfield in the contiguous United States.[14]
  11. The largest known 'wildcat' oil gusher blew near Qom, Iran on August 26, 1956. The uncontrolled oil gushed to a height of 52 m (170 ft), at a rate of 120,000 barrels (19,000 m3) per day. The gusher was closed after 90 days' work by Bagher Mostofi and Myron Kinley (USA).[15]
  12. One of the most troublesome gushers happened on June 23, 1985 at the well #37 at the Tengiz field in Atyrau, Kazakh SSR, Soviet Union, where the deep, 4209 metre well blew out and the 200-metres high gusher self-ignited two days later. Oil pressure up to 800 atm and high hydrogen sulfide content had led to the gusher being capped only on 27 July, 1986 when the well was closed by the shaped charge. The total volume of erupted material measured at 4.3 millions metric tons of oil, 1.7 bn m³ of natural gas, and the burning gusher resulted in 890 tons of various mercaptans and more than 900000 tons of soot released into atmosphere.[16]
  13. The largest underwater blowout in U.S. history occurred on April 20, 2010, in the Gulf of Mexico at the Macondo Prospect oil field. The blowout caused the explosion of the Deepwater Horizon, a mobile offshore drilling platform owned by Transocean and under lease to BP at the time of the blowout. While the exact volume of oil spilled is unknown, as of June 3, 2010 (2010 -06-03), the United States Geological Survey (USGS) Flow Rate Technical Group has placed the estimate at between 35,000 to 60,000 barrels (5,600 to 9,500 m3) of crude oil per day.[17]

Cause of blowouts

Reservoir pressure

Petroleum or crude oil is a naturally occurring, flammable liquid consisting of a complex mixture of hydrocarbons of various molecular weights, and other organic compounds, that are found in geologic formations beneath the Earth's surface. Because most hydrocarbons are lighter than rock or water, they often migrate upward through adjacent rock layers until either reaching the surface or becoming trapped within porous rocks (known as reservoirs) by impermeable rocks above. However, the process is influenced by underground water flows, causing oil to migrate hundreds of kilometres horizontally or even short distances downward before becoming trapped in a reservoir. When hydrocarbons are concentrated in a trap, an oil field forms, from which the liquid can be extracted by drilling and pumping. The down hole pressures experienced at the rock structures change depending upon the depth and the characteristic of the source rock.

Formation kick

The downhole fluid pressures are controlled in modern wells through the balancing of the hydrostatic pressure provided by the mud used. Should the balance of the drilling mud pressure be incorrect then formation fluids (oil, natural gas and/or water) begin to flow into the wellbore and up the annulus (the space between the outside of the drill string and the walls of the open hole or the inside of the last casing string set), and/or inside the drill pipe. This is commonly called a kick. If the well is not shut in (common term for the closing of the blow-out preventer valves), a kick can quickly escalate into a blowout when the formation fluids reach the surface, especially when the influx contains gas that expands rapidly as it flows up the wellbore, further decreasing the effective weight of the fluid. In other petroleum engineering words, the formation pore pressure gradient exceeds the mud pressure gradient, even in some cases when the Equivalent Circulating Density ECD is imposed with the mud pumps on the rig.

Additional mechanical barriers such as blowout preventers (BOPs) can be closed to isolate the well while the hydrostatic balance is regained through circulation of fluids in the well.

Early warning signs of a well kick are:

[18]

The primary means of detecting a kick is a relative change in the circulation rate back up to the surface into the mud pits. The drilling crew or mud engineer keeps track of the level in the mud pits and/or closely monitors the rate of mud returns versus the rate that is being pumped down the drill pipe. Upon encountering a zone of higher pressure than is being exerted by the hydrostatic head of the drilling mud at the bit, an increase in mud returns would be noticed as the formation fluid influx pushes the drilling mud toward the surface at a higher rate. Conversely, if the rate of returns is slower than expected, it means that a certain amount of the mud is being lost to a thief zone somewhere below the last casing shoe. This does not necessarily result in a kick (and may never become one); however, a drop in the mud level might allow influx of formation fluids from other zones if the hydrostatic head at depth is reduced to less than that of a full column of mud.

Well control

The first response to detecting a kick would be to isolate the wellbore from the surface by activating the blow-out preventers and closing in the well. Then the drilling crew would attempt to circulate in a heavier kill fluid to increase the hydrostatic pressure (sometimes with the assistance of a well control company). In the process, the influx fluids will be slowly circulated out in a controlled manner, taking care not to allow any gas to accelerate up the wellbore too quickly by controlling casing pressure with chokes on a predetermined schedule.

This effect will be minor if the influx fluid is mainly salt water. And with an oil-based drilling fluid it can be masked in the early stages of controlling a kick because gas influx may dissolve into the oil under pressure at depth, only to come out of solution and expand rather rapidly as the influx nears the surface. Once all the contaminant has been circulated out, the casing pressure should have reached zero.

Capping stacks are used for controlling blowouts. The cap is an open valve that is closed after bolted on.http://www.jwco.com/technical-litterature/p10.htm

Types of blowouts

Well blowouts can occur during the drilling phase, during well testing, during well completion, during production, or during workover activities.[1]

Surface blowouts

Blowouts can eject the drill string out of the well, and the force of the escaping fluid can be strong enough to damage the drilling rig. In addition to oil, the output of a well blowout might include sand, mud, rocks, drilling fluid, natural gas, water, and other substances.

Blowouts will often be ignited by an ignition source, from sparks from rocks being ejected, or simply from heat generated by friction. A well control company will then need to extinguish the well fire or cap the well, and replace the casing head and hangars. The flowing gas may contain poisonous hydrogen sulfide and the oil operator might decide to ignite the stream to convert this to less hazardous substances.

Sometimes, blowouts can be so forceful that they cannot be directly brought under control from the surface, particularly if there is so much energy in the flowing zone that it does not deplete significantly over the course of a blowout. In such cases, other wells (called relief wells) may be drilled to intersect the well or pocket, in order to allow kill-weight fluids to be introduced at depth. When first drilled in the 1930s relief well were drilled to inject water into the main drill well hole. [19] Contrary to what might be inferred from the term, such wells generally are not used to help relieve pressure using multiple outlets from the blowout zone.

Subsea blowouts

Subsea wells have the wellhead and pressure control equipment located on the seabed. They vary from depths of 10 feet (3.0 m) to 8,000 feet (2,400 m). It is very difficult to deal with a blowout in very deep water because of the remoteness and limited experience with this type of situation.[20]

The Deepwater Horizon well blowout in the Gulf of Mexico in April 2010, in 5,000 feet (1,500 m) water depth, is the deepest subsea well blowout to date.

Underground blowouts

An underground blowout is a special situation where fluids from high pressure zones flow uncontrolled to lower pressure zones within the wellbore. Usually this is from deeper higher pressure zones to shallower lower pressure formations. There may be no escaping fluid flow at the wellhead. Underground blowouts can be very difficult to bring under control, and if left unchecked the fluids may find their way to the surface or ocean floor nearby.

Blowout control expertise

Myron M. Kinley was a pioneer in fighting oil well fires and blowouts. He developed many patents and designs for the tools and techniques of oil firefighting. His father, Karl T. Kinley, attempted to extinguish an oil well fire with the help of a massive explosion — a method that remains a common technique for fighting oil fires. The first oil well put out with explosives by Myron Kinley and his father, was in 1913.[21] Kinley would later form the M.M. Kinley Company in 1923.[21]

Paul N. "Red" Adair joined the M.M. Kinley Company in 1946, and worked 14 years with Myron Kinley before starting his own company, Red Adair Co., Inc., in 1959. Asger "Boots" Hansen and Edward Owen "Coots" Matthews also begin their careers under Kinley.

Red Adair co. has helped in controlling many offshore blowouts, including;

In 1994, Adair retired and sold his company to Global Industries. Management of Adair's company left and created International Well Control (IWC). In 1997, they would buy the company Boots & Coots International Well Control, Inc., which was founded by two former lieutenants of Red Adair in 1978.

Methods of quenching blowouts

Although several experimental methods exist which attempt to capture as much oil as possible from a blown out well, they are very far from perfect, capturing between 20% - 50% of the leaking oil, by optimistic estimates. Ideally, the well could be made to stop gushing oil entirely - thus putting a stop to the cumulating pollution.

Use of nuclear explosions

On Sep. 30, 1966 the Soviet Union in Urt-Bulak, an area about 80 kilometers from Bukhara, Uzbekistan, experienced blowouts on five natural gas wells. It was claimed in Komsomoloskaya Pravda that after years of burning uncontrollably they were able to stop them entirely.[23] The Soviets lowered a specially made 30 kiloton nuclear bomb into a 6 kilometres (20,000 ft) borehole drilled 25 to 50 metres (82 to 160 ft) away from the original (rapidly leaking) well. A nuclear explosive was deemed necessary because conventional explosive both lacked the necessary power and would also require a great deal more space underground. When the bomb was set off, it proceeded to crush the original pipe that was carrying the gas from the deep reservoir to the surface, as well as to glassify all the surrounding rock. This caused the leak and fire at the surface to cease within approximately one minute of the explosion, and proved over the years to have been a permanent solution. A second attempt on a similar well was not as successful and other tests were for such experiments as oil extraction enhancement (Stavropol, 1969) and the creation of gas storage reservoirs (Orenburg, 1970). As nuclear historian Robert S. Norris notes in the Times, all these Soviet nuclear blasts were on land and did not involve oil. That being the case, the general principles involved are the same.[24]

Notable offshore well blowouts

Data from industry information.[1][25]

Year Rig Name Rig Owner Type Damage / details
1955 S-44 Chevron Corporation Sub Recessed pontoons Blowout and fire. Returned to service.
1959 C. T. Thornton Reading & Bates Jackup Blowout and fire damage.
1964 C. P. Baker Reading & Bates Drill barge Blowout in Gulf of Mexico, vessel capsized, 22 killed.
1965 Trion Royal Dutch Shell Jackup Destroyed by blowout.
1965 Paguro SNAM Jackup Destroyed by blowout and fire.
1968 Little Bob Coral Jackup Blowout and fire, killed 7.
1969 Wodeco III Floor drilling Drilling barge Blowout
1969 Sedco 135G Sedco Inc Semi-submersible Blowout damage
1969 Rimrick Tidelands ODECO Submersible Blowout in Gulf of Mexico
1970 Stormdrill III Storm Drilling Jackup Blowout and fire damage.
1970 Discoverer III Offshore Co. Drillship Blowout (S. China Seas)
1971 Big John Atwood Oceanics Drill barge Blowout and fire.
1971 Unknown Floor Drilling Drill barge Blowout and fire off Peru, 7 killed.
1972 J. Storm II Marine Drilling Co. Jackup Blowout in Gulf of Mexico
1972 M. G. Hulme Reading & Bates Jackup Blowout and capsize in Java Sea.
1972 Rig 20 Transworld Drilling Jackup Blowout in Gulf of Martaban.
1973 Mariner I Sante Fe Drilling Semi-sub Blowout off Trinidad, 3 killed.
1975 Mariner II Sante Fe Drilling Semi-submersible Lost BOP during blowout.
1975 J. Storm II Marine Drilling Co. Jackup Blowout in Gulf of Mexico.
1976 Petrobras III Petrobras Jackup No info.
1976 W. D. Kent Reading & Bates Jackup Damage while drilling relief well.
1977 Maersk Explorer Maersk Drilling Jackup Blowout and fire in North Sea
1977 Ekofisk Bravo Phillips Petroleum Platform Blowout during well workover.[26]
1978 Scan Bay Scan Drilling Jackup Blowout and fire in the Persion Gulf.
1979 Salenergy II Salen Offshore Jackup Blowout in Gulf of Mexico
1979 Sedco 135F Sedco Drilling Semi-submersible Blowout and fire in Bay of Campeche Ixtoc I well.[26]
1980 Sedco 135G Sedco Drilling Semi-submersible Blowout and fire of Nigeria.
1980 Discoverer 534 Offshore Co. Drillship Gas escape caught fire.
1980 Ron Tappmeyer Reading & Bates Jackup Blowout in Persian Gulf, 5 killed.
1980 Nanhai II Peoples Republic of China Jackup Blowout of Hainan Island.
1980 Maersk Endurer Maersk Drilling Jackup Blowout in Red Sea, 2 killed.
1980 Ocean King ODECO Jackup Blowout and fire in Gulf of Mexico, 5 killed.[27]
1980 Marlin 14 Marlin Drilling Jackup Blowout in Gulf of Mexico
1981 Penrod 50 Penrod Drilling Submersible Blowout and fire in Gulf of Mexico.
1985 West Vanguard Smedvig Semi-submersible Shallow gas blowout and fire in Norwegian sea, 1 fatality.
1981 Petromar V Petromar Drillship Gas blowout and capsize in S. China seas.
1988 Ocean Odyssey Diamond Offshore Drilling Semi-submersible Gas blowout at BOP and fire in the UK North Sea, 1 killed.
1989 Al Baz Sante Fe Jackup Shallow gas blowout and fire in Nigeria, 5 killed.[28]
1993 Actinia Transocean Semi-submersible Sub-sea blowout in Vietnam. .[29]
2001 Ensco 51 Ensco Jackup Gas blowout and fire, Gulf of Mexico, no casualties[30]
2002 Arabdrill 19 Arabian Drilling Co. Jackup Structural collapse, blowout, fire and sinking.[31]
2004 Adriatic IV Global Sante Fe Jackup Blowout and fire at Temsah platform, Mediterranean Sea[32]
2007 Usumacinta PEMEX Jackup Storm force rig to move, causing well blowout on Kab 101 platform, 22 killed.[33]
2009 West Atlas / Montara Seadrill Jackup / Platform Blowout and fire on rig and platform in Australia.[34]
2010 Deepwater Horizon Transocean Semi-submersible Blowout and fire on the rig, subsea well blowout, killed 11 in explosion.
2010 Vermilion Block 380 Mariner Energy Platform Blowout and fire, 13 survivors, 1 injured.[35][36]

See also

References

  1. ^ a b c d e 'All About Blowout', R. Westergaard, Norwegian Oil Review, 1987 ISBN 82-991533-0-1
  2. ^ a b http://www.sjgs.com/lakeview.html
  3. ^ Walsh, Bryan (2010-05-19). "Gulf Oil Spill: Scientists Escalate Environmental Warnings". Time. http://www.time.com/time/health/article/0,8599,1990171,00.html. Retrieved June, 2010. 
  4. ^ http://www.rootsweb.com/~txnavarr/business/oil_industry/hughes_and_mckie_oil_well_fire/index.htm
  5. ^ http://aoghs.org/technology/end-of-gushers/
  6. ^ http://www.asme.org/Communities/History/Landmarks/First_RamType_Blowout.cfm
  7. ^ "The Shaw Gusher". The Village of Oil Springs. http://www.oilsprings.ca/todo.htm. Retrieved 20111-02-23. 
  8. ^ http://www.sjgs.com/gushers.html#spindletop
  9. ^ http://www.todayinsci.com/5/5_26.htm
  10. ^ http://www.signal-hill.ca.us/administration/history.php
  11. ^ http://www.propuestas.reacciun.ve/Servidor_Tematico_Petroleo/documentos_articulos6.html#petroleo7
  12. ^ http://members.autobahn.mb.ca/~het/paras2.html
  13. ^ http://www.energybulletin.net/4720.html
  14. ^ http://www.easttexasoilmuseum.com/Pages/history.html
  15. ^ http://books.google.com/books?id=1_j80DzhifgC&dq=qum+1955+%222+million%22+gusher&q=qum#search_anchor
  16. ^ Christopher Pala (2001-10-23). "Kazakhstan Field's Riches Come With a Price". 82. The St. Petersburg Times. http://www.sptimes.ru/index.php?action_id=2&story_id=5705. Retrieved 2009-10-12. 
  17. ^ "Oil estimate raised to 35,000-60,000 barrels a day". CNN. 2010-06-15. http://www.cnn.com/2010/US/06/15/oil.spill.disaster/index.html?hpt=T1&iref=BN1. Retrieved 2010-06-15. 
  18. ^ Grace, R: Blowout and Well Control Handbook, page 42. Gulf Professional Publishing, 2003
  19. ^ "Wild Oil Well Tamed by Scientific Trick" Popular Mechanics, July 1934
  20. ^ Ultra-deepwater blowouts - how could one happen, Offshore Magazine, 1 Jan 1997, Larry H. Flak, Boots & Coots
  21. ^ a b Boots & Coots History Page : http://www.boots-coots.com/members/history.html
  22. ^ Red Adair website
  23. ^ Link to and translation of article in Komsomoloskaya Pravda regarding the use of nuclear weapons by the Russians to plug oil leaks (translate.google.com)
  24. ^ YouTube - An Atomic Bomb Will Stop the Oil Leak
  25. ^ Rig disaster Website : http://home.versatel.nl/the_sims/rig/i-blowout.htm
  26. ^ a b Oil Rig Disasters Website : http://home.versatel.nl/the_sims/rig/ixtoc1.htm
  27. ^ http://openjurist.org/813/f2d/679/incident-v-ocean
  28. ^ Rig Disaster Website : http://home.versatel.nl/the_sims/rig/albaz.htm
  29. ^ http://home.versatel.nl/the_sims/rig/actinia.htm
  30. ^ Oil Rig Disasters website : http://home.versatel.nl/the_sims/rig/ensco51.htm
  31. ^ Oil Rig Disasters Website : http://home.versatel.nl/the_sims/rig/ad19.htm
  32. ^ Oil Rig Disasters Website : http://home.versatel.nl/the_sims/rig/adriatic4.htm
  33. ^ Usumacinta website : http://home.versatel.nl/the_sims/rig/usumacinta.htm
  34. ^ [1], ABC
  35. ^ September 2 oil rig explosion, CNN
  36. ^ New oil rig explosion in Gulf of Mexico WFRV

External links